1.购买材料/Purchasing Materials
热浸锌方管
Hot-dip galvanized square tube
6000*100*100*3
热浸锌方管
Hot-dip galvanized square tube
6000*100*50*3
一寸镀锌水管
One inch galvanized water pipe
6000*34
名称 name | 型号(长*宽*高*厚) Model (length * width * height * thickness) | 数量 number |
热浸锌方管 Hot-dip galvanized square tube | 6000*100*100*3 | 3 |
热浸锌方管 Hot-dip galvanized square tube | 6000*100*50*3 | 2 |
一寸镀锌水管 One inch galvanized water pipe | 6000mm长 | 2 |
2.切割材料/Profile cutting
热浸锌方管6000*100*100*3,一共三只,如左图标识的裁切成3200mm两只,2200mm四只。 一寸镀锌水管6000mm,一共两只,如左图标识切割成2500mm一只,2000mm两只。 其余的为多余的废料。 Hot dip galvanized square tubes 6000 * 100 * 100 * 3, a total of three pieces, cut into 3200mm two pieces and 2200mm four pieces as marked in the left image. One inch galvanized water pipe is 6000mm, with a total of two pieces. As shown in the left image, cut it into one 2500mm piece and two 2000mm pieces. The rest is surplus waste.
3.焊接调节底座
焊接调节底座 ,M16X150镀锌螺丝16只,M16螺帽48只,M16垫片32只。 Welding adjustment base, 16 M16X150 galvanized screws, 48 M16 nuts, and 32 M16 washers.
4.焊接立柱
焊接立柱,2.2米10厘米*10厘米*3毫米立柱4根,底座钣金4片。 Welding columns, 2.2m 10cm * 10cm * 3mm, 4 columns, 4 base sheet metal pieces。
5.手臂横杆打孔
手臂横杆打孔,2.5米一寸镀锌水管一根,开孔尺寸直径11毫米通孔。 Drill holes on the arm crossbar, one 2.5-meter-inch galvanized water pipe, with a diameter of 11mm through hole.
6.手臂折弯打孔
手臂折弯打孔,两米长一寸镀锌水管2根,折弯角度150度,开孔直径11毫米通孔。 Arm bending and punching, two one inch galvanized water pipes with a length of two meters, a bending angle of 150 degrees, and a hole diameter of 11 millimeters.
7.钣金喷漆
钣金喷漆,漆料颜色根据自己喜好选择,用漆量大约1.5千克。 Sheet metal spray painting, paint color selection according to one's own preferences, with a paint amount of approximately 1.5 kilograms.
8.安装场地弹线
安装场地弹线,安装场地最小尺寸。长6.3米宽3.5米高2.6米。在场地的合适位置用墨斗弹出长6米宽3.2米的设备安装尺寸。 Snap the line on the installation site and ensure the minimum size of the installation site. 6.3 meters long, 3.5 meters wide, and 2.6 meters high. Use an ink fountain to eject equipment installation dimensions of 6 meters long and 3.2 meters wide at a suitable location on the site.
9.固定调节底座
10.安装调整立柱
11.固定轨道
12.固定拉紧钢丝绳